Emaar Enterprise

• Cleans, lubricates, protects, penetrates, and loosens corrosion
• Prevents corrosion by displacing moisture
• Restores resistance values by reducing current leakage
• Provides precision lubrication by its thin, high dielectric strength, lubricating film
• Helps restore water-damaged electrical equipment
• Frees rusted or seized parts by penetrating under dirt and scale into the finest pores and cracks
• Can be used on all metals and alloys
• Will not harm modern plastics, painted surfaces, coatings and rubbers
• Convenient 360° (upside-down) spray valve for aerosols
• Non-flammable CO2 propellant, giving an active product content of 97%

• NSN 6850-00-874-5847
• USDA CLASS H2

• Electrical connectors
• Relays
• Circuit breakers
• Transformers
• Switch gears
• Motors
• Generators
• Controls
• Instruments
• Communication assemblies
• Electronics
• Alarm systems
• Starters.

• Spray light even coat to protect surfaces and to seal out moisture.
• Apply liberally to loosen rusted/seized parts; full penetration may require several hours.
• To displace water, spray wet surfaces until run-off is clear and moisture free. When possible, dip water damaged equipment in CRC 2-26; agitate while submerged; remove and allow to drain. A detailed "CRC water damage restoration" procedure is available upon request.
• To be removed by CRC Lectra Clean II, hydrocarbon solvents or alkaline degreasing before surface treatment.
• For application of CRC 2-26 in dipping baths, customers should take care to stir from time to time (to distribute small amounts of deposits) and to prevent excessive evaporation of solvent.When stable emulsions have been formed, the bath should be emptied and cleaned, and the product replaced.
• Do not use on energised equipment; allow solvent to evaporate before energising.This evaporation may take up to 4 hours, depending on surface condition and environment. Use only in well ventilated area.
• A safety data sheet (MSDS) according EU93/112 is available for all CRC products.

• Multipurpose service spray. Loosens rusted parts. Displaces moisture, enables to start wet engines, prevents electrical failure. Lubricates, stops squeaks and squeals, frees sticking mechanisms. Protects metals against humidity, corrosive atmosphere and prevents rust.

• Displaces moisture, starts wet engines, prevents electrical failures. Lubricates, loosens seized and rusted mechanisms. Protects against humidity, prevents rust. 

CRC 3-36 is based on a paraffinic oil and a multiple organic inhibitor system that prevents rust and corrosion by displacing and sealing out moisture and by forming a continuous protection barrier against water and oxygen.The oily, almost invisible film of CRC 3-36 lubricates and penetrates into the finest pores and cracks of the surface. CRC 3-36s effectiveness for surface protection is derived from three of its principal properties :
Affinity for metal
Low surface tension
High capillary action.

By its affinity for metal and low surface tension CRC 3-36 displaces moisture and separates it from contact with the metal surface. The high capillary action contributes to the great spreading power.

Process Manufacturing :
Heat treated parts
Machined surfaces
Finished welds
In-process aluminium extrusions
Precision mechanisms

Machining :
Fixtures
Dies

Material Storage :
Tubings
Castings
Gears
Weld rod and wire

Maintenance :
Air actuated tools
Conveyors
Frozen joints
Locks
Hoists

Directions :
Spray in light, even films to lubricate and protect metal surfaces. For electrostatic spraying, addition of polar solvents (butanol, nitropropane,) may be necessary.
Apply liberally and allow to penetrate to free rusted parts. Full penetration may require several hours.
To displace moisture, spray wet surfaces until run-off is clear and moisture-free.
To be removed by solvent cleaners (CRC Industrial Degreaser, CRC Fast Dry Degreaser) or alkaline degreasing before surface treatment.
For application of CRC 3-36 in dipping baths, customers should take care to stir from time to time (to distribute small amounts of deposits) and to prevent excessive evaporation of solvent.When stable emulsions have been formed, the bath should be emptied and cleaned, and the product replaced.
Do not use on energized equipment. Use in a well ventilated area.
A safety data sheet (MSDS) according EU-Directive 93/112 is available for all CRC products.

1. GENERAL DESCRIPTION A single component, zinc-aluminium coating combining corrosion protection properties with the lustre look of aluminium. Galva Brite is a combination of zinc and aluminium powders, resins and additives, formulated to form a flexible protective film with a bright, glossy appearance. 2. FEATURES • Excellent touch-up for galvanized surfaces. • Provides excellent corrosion and rust resistance to ferrous metals. • Unique combination of flexibility and hardness. • Resists rusting, peeling and fading. • Adheres well to metal surfaces. • Combines the galvanized look with the convenience of an aerosol application. • Totally lead and chromate free. • No chlorinated solvents. • Aerosols use dimethylether (DME) propellant for controlled spray and film properties.